| Product
Name |
Description |
Features /
benefits |
Typical
Applications |
Technical Information
|
Dosage / coverage |
Packing
Available |
Complies
with
Engineers spec
CRD-C-621-83 &
ASTM-C-1107
Grade C |
High
strength,
Non-shrink, Free
flow Grout for
foundations |
●
Highly fluid and extremely place able for
easy field use
● High strength for maximum
load bearing
on shrink with minimum positive
Expansion for high tolerance performance
● Non-bleeding and
non-segregating at fluid
consistency
● Does not contain any
chlorides or additives pre contribute to corrosion of
construction
● Non-bleeding and non-segregating at fluid
consistency
● Does not contain any
chlorides or additives pre-
contribute to corrosion of construction, Anchorage
● Total shrinkage compensation
which
provides a maximum bearing surface for the greatest
overall support
● Rapid strength gain to
minimize turn around
time for equipment reg routs
● Excellent working time at
high ambient temperatures
Shelf Life : 6 Months |
●
Heavy Machinery and Bridge bearing pad equipment
foundations
● Boiler foundation,
Pump
foundations, Cavities, Gaps and recesses,
Structural columns in pre-cast Crane rail construction,
Anchorage |
●
Density : 2,250 ± 50
(kg/m³) ·
● Compressive Strength at
W/P ratio 0.15 (IS: 4031-1988 / ASTM C-109)
1day -18MPa
7 days - 35 MPa 28 days - 50 MPa
● Compressive strength is
related to water powder ratio (0.13 to 0.15)
● Flow - Table Flow (without
vibrations) :
- More than 210 mm when water
- Powder ratio greater than 0.14.
● Restrained Expansion (after
28 days)
● Setting time at W/P ratio
0.14 (IS:4031-1988
Part 5, ASTM C -191)
- Initial Set - > 300 mins
- Final Set - < 600 mins
● Flexural Strength :
1 day - 2.75 MPa
7 days - 5.3 MPa
28 days- 7.1MPa
|
Yield = 27.25
litres per pack |
50kg
bag |
Pldlgrout
10M
Complies with
Engineers spec CRD-C-621-83 & ASTM-C-1107
|
High
strength,
Non shrink, Free
flow Grout for foundations |
●
Non-shrink with concerned positive
expansion
● High flowability and
excellent pourability
for easy field use
● Non-bleeding and
non-segregating at fluid
consistency
● Excellent for dynamic and
static loading conditions
● High early strength - quick
turn around
● Free of chlorides and
additives, that may
lead to corrosion
● High drill resistance
property
● Self compacting
Shelf Life : 6 Months
|
●
Heavy machinery and Bridge bearing pad equipment
foundations
● Boiler foundation, Turbine generator bearing plates,
Cavities, Gaps and recesses, Structural columns in
pre-cast Crane rail construction, Anchorage
|
●
Density -
2,217 :I: 50 (kg/m3)
● Compressive Strength
(IS: 4031-1988) :
24 hrs, more than 300 kg/cm2 7 days, more than 550
kg/cm2
28 days, more than 650 kg/cm2
● Compressive strength is
related to water powder ratio (0.14 to 0.16)
● Flow - Table Flow (without
vibrations) :
More than 260 mm when water powder ratio greater than
0.15.
● Expansion
Restrained condition
0.15 to 0.4 %
Unrestrained expansion upto 2% in plastic state Setting
time (IS:4031-1988 Part 5)
Initial Set:> 300 mins
Final Set: < 600 mins |
Yield = 26.16 litres
per pack at 0.16 w/p ratio |
50 kg bag |
| Pldigrout
EG-3 |
3 component
Epoxy Based
Resin free flow grout |
●
Dr. Fixit Pidigrout EG-3S has a pourable
consistency for gap width from 10 mm to com
65 mm
● Dr. Fixit Pidigrout EG-3L
has a pourable consistency for gap with above 65 mm to
pla 120 mm
● Attains very good early
strengths
● Good chemical resistance to
a wide range of acids, alkalies, oils, etc.
● Good tensile and flexural
strengths, it has
very good dynamic load resistance.Excellent bond
strength with concrete and steel.
● Low creep under continuous
loads.Resists non-oxidising mineral acids, alkali dilute
acids, some organic acids and solvents.
● Provides corrosion
protection to both in
concrete foundations and machines of concrete and steel
shelf Life : 1 Year |
Foundations of large
compressors, pumps, turbines, rail grouting,
keyways, inverted base plates, precast bridge
sections, etc.
|
●
Pot life : Approx. 45 mins at 30° C ( For 7.5 kg
mix)
● Specific gravity: 2.15
± 0.02
● Compo Strength:
7 days - 90 N/ mm2 approx. (EG-3S)
7 days - 80 N/ mm2 approx. (EG-3L)
● Tensile Strength: 12 N/mm2
approx. at 7 days ( EG-3S)
● 11 N tmm2 approx at 7 days (
EG-3L)
● Elongation at Break: 1 % (
EG-3S )
1.1% (EG-3L)
● Bond Strength :
25 Nt mm2 at 14 days ( EG-3S)
22 Nt mm2 at 14 days ( EG-3L)
|
|
7.5 kg
composite pack = 3.5 Itrs. Yield (approx. |
